Make Your Own Steroids Injections

Make Your Own Steroids Injections

Instead of buying finished steroid injections,there are many benefits for making your own injectable steroids:

1.The cost is only 40-60% of the normal cost
2.They take only a short time to prepare
3.They are easier and cheaper to ship than amps or vials
4.Less chance of your order getting seized by customs
5.Unlike vials and amps, they come with a refund/reship policy

Example Recipe:

100ml test enan 250mg/ml

Test Enan Powder……………….. 25g  (about 18.75ml)

Benzyl Alcohol (USP)……………..2ml   (2%)

Benzyl Benzoate (USP)………….18ml  (10%)

Grape Seed Oil…………………….61.25ml

Tools & Devices needed:

Digital Scale 0.1g or 0.01g

Small piece of paper

100ml Beaker and Glass Rod

A frying Pan

3ml syringe with 18-21 gauge needle

20ml or 60 ml syringe with 18-21 gauge needle

0.22um Syringe Filter

10 set of 10ml Vials (A whole set=vial+rubber stopper+cap)

Hand Crimper

Steps for Making Steroid Injections:

Step #1.  Weigh Test Enan Powder:

You have to do this very carefully. get your small piece of paper and place it on the scale then press tare to set it to zero so it doesnt weigh the paper. Then slowly add your powder. Now here is the tricky part the powder weighs so little that the scale needs to be reset every time you add some. All you have to do is add some then press on the scale with your finger and let the number fall back down. Once you get 25 grams your good to go.

 

Step #2.   Add powder,BA,BB into the beaker:

1.Dump the powder into your beaker;

2.Then Add 2ml of Benzyl Alcohol (BA) (USP);

3.Then add 18ml of Benzyl Benzoate BB) (USP);

 

Step #3.  Heating in Water Bath (This Step is optional but it makes things easy)

1.Get a pot with a bout an inch of water in it and place it on the stove and set the eye to heat;

2.Put the beaker in the Pan,Pace the beaker into a few cm of water in a Pan or something similar;

3.Watch the powder,when it dissolved and the mixture get pretty close to clear

Once that’s done, then we get the melted mixture.

Note: It is important not to use water that is too hot because this will cause some products to oxidize-150f is a good temperature to use, alternatively boiled water from the kettle. The carrier oil should be the same temperature as the solution when it is added so if you warm the solution in a water bath you should also the same to the carrier oil.The objective at this point is simply to fully dissolved the powder into the solvents. There should be no “Hormone swirls” or any visible powder remaining in the solution and once this is achieved move on to the next step.

Step #4.  Add Grape Seed Oil

Next wait the mixture cool down a little, then add your grape seed oil and let it all warm up again for a bit to make filtering a little bit faster.

Step #5:Filtering.

Draw up the solutions into the syringe you will be filtering with, this can be a single large syringe or this can be repeated multiple times with a smaller syringe. Remove the 0.22um sterile syringe filter from it’s packing and fix the green needle to the smaller side and then apply to the syringe.Wipe the top of the sterile vial with an Alcohol swab and insert the green needle in it, put the needle attached to the syringe filter into the vial as shown below:

Notes: The second needle equalizes the pressure as the solution enters the vial. Apply pressure to the syringe plunger to the filter the mixture. This is the most important part of this entire process as it is what sterilizes your product. All finished steroids from any steroid lab must go through this very process.Occasionally one may find that the filter gets blocked or that the process slows drastically-it is acceptable to replace the filter with a new one if this occurs to save time. The time it takes to filter steroids depends on which steroid is being filtered and how much is being filtere, as well as the mg/ml of the product.Once the product is filtered in the sterile vial the process is complete.

Also you can use a syringe to draw out of the air from the Vials.

Step #6:Crimp them with flip off caps.

Posted in Homebrew steroids guide.