how to make injectable Lidocaine Hcl

What you’ll need

Lidocaine Hydrochloride (HCL) powder (roughly $1 per gram in small quantities)

Sterile saline, or distilled water (varies, $10 for 24 of the single-use saline vials I chose)

Thermometer, accurate up to 200 degrees F or so ($10 and up)

Scale, accurate down to 1mg or less. ($25 and up)

Funnel, small

Surgical clamp


A clean work area with a stove or other way to heat water

Lidocaine Hydrochloride (HCL) powder is available in lab grades and pharmaceutical grade from if you can’t obtain it in USP grade.  You want “Lidocaine HCL” which is water soluble, not the straight “Lidocaine powder” or “Lidocaine base” which isn’t.  It should be stored at room temperature according to its Material Safety Data Sheet, and has no predetermined shelf life or expiration date if stored in an airtight container – or at least none that I’ve been able to determine anyway.

The supplies and materials I used:

The isopropyl alcohol shown above isn’t part of the solution, it’s used for cleaning the equipment.  Before you begin, all the equipment and anything they might touch, including you, should be thoroughly cleaned with a disinfectant or antiseptic.  Boil any items that can be.  Scrub and glove your hands.

For the sterile saline, I chose a type packaged in 15ml plastic vials and marketed for nasal irrigation purposes.  Search on “ModuDose” and you’ll find it .  Mine were dated as expiring in one year, I plan to use them beyond that date unless they turn cloudy or have particulates in them.

I like this particular kind as they’re the perfect size for creating single doses with minimal waste, and they lessen the chance of contamination by not having to mix and transfer the solution between multiple containers during the process.

To produce a 2% lidocaine HCL solution (weight/volume), weigh out 0.3 grams (300mg) of lidocaine HCL, snip the top of the 15ml saline vial about half way down the neck with scissors, insert the funnel securely into the neck of the vial, and pour the lidocaine HCL powder into the funnel.

The powder tends to stick to the funnel, so you’ll probably need to gently squeeze the vial to force the saline up into the funnel, then release to allow the saline to flow back down into the vial carrying the lidocaine HCL powder with it.  Repeat as necessary to get all the lidocaine into the vial. Remove the funnel, and seal the neck of the saline/lidocaine vial using a surgical clamp or needle holder.

With the 2% lidocaine/saline solution vial now sealed shut, place the vial into a small pan of normal tap water, being careful not to submerge it fully – we don’t want any tap water to enter the vial.  Heat the water past 176 degrees Fahrenheit (I found it easiest to place a small glass filled with tap water into the pan the water, like a double boiler) and allow it to remain slightly above that temperature for 2-3 minutes.  Lidocaine HCL melts at 176 degrees F (80C), and dissolves in water.  Allowing the lidocaine HCL to melt, not just dissolve, in the saline ensures even distribution with no chance of particulates.  If particulates do remain at this point, they’re not lidocaine HCL and the solution shouldn’t be used.

Remove the vial from the pan, and keeping it securely clamped closed, allow it to cool.  You now have 15ml of 2% lidocaine HCL ready for use, which is also about the maximum recommended safe dosage for an adult.

Use it the same as you would any other vial of Rx injectable solution:  With the vial still clamped shut, clean a section near the top of the vial with an alcohol pad, invert the vial, insert the needle through the plastic section just cleaned, and draw out the desired amount into the syringe.

For different amounts of solution, or to make it in different concentrations, the formula is:

[Weight of lidocaine in grams  /  Volume of saline in milliliters] x 100.  For example, 1 gram lidocaine / 100 milliliters of saline = .01 X 100 = 1% solution.

As my first real test, I used a 0.5ml insulin syringe with a 30G needle, and performed three injections for a total of 1.5ml of 2% lidocaine in a 1″ square area just above the knee.  In a real situation a 6-10ml syringe with a longer needle would probably be better, I just have a lot of insulin needles stored so I used them instead.  Surprisingly, there was no sting from the lidocaine solution over that of the saline alone (tested first as the control).  I had expected some mild stinging, as is normally reported with Rx lidocaine without any sodium bicarbonate solution added, but there was no noticable difference.

Anesthetic effect was good and as expected.  In other words, the area injected and the immediate vicinity around it was completely numb.  Hospital / Clinic / Prescription Strength numb.  It reached full effect in about 10 minutes, and lasted a little over 30 minutes total before wearing off rather quickly.  The lack of epinephrine and, I suspect, the lower viscosity of the saline used here than in the lidocaine solution available by Rx probably allows it to disperse, and wear off, faster.  In further testing, I’ve used up to 6ml of 2% lidocaine in a single application, and even had some success at performing digital (fairly easy) and radial (not so much) nerve blocks.

In closing, I think it’s safe to assume that the solution should be used within 24 hours and any leftover discarded since it doesn’t contain any preservatives or antibacterials.  With practice and the materials handy it only takes about 20 minutes to make more.  I created a small kit with all the supplies, including pre-weighed lidocaine packets in tiny zip-loc bags that are clearly marked, in case I need to make it in a hurry.  Hope no one ever needs to.


(1) Most sources of Lidocaine HCL that I found listed it as “Reagent ACS” grade, which is not for any medical use.  But that grade does require certification by the American Chemical Society, who tests batches from a production run and provides a Certificate of Analysis (COA) to the manufacturer as part of their certification.

A description of the different chemical grades is available here:

Many sellers will provide this COA on request, but who can say what contamination may have occurred while the seller was repackaging the product into smaller quantities for retail sale?  Or even that the COA is from the same batch they sold you?   If that concerns you then it might help to consider that  thousands, if not millions, of people are snorting this same Reagent ACS grade lidocaine daily, as it’s a common dilutant added to street cocaine.

It’s also a fair question to ask if lab grade chemicals today are less pure than medical grade chemicals used 50-100 years ago.  But then again, what if your seller confused your lidocaine order with someone else’s strychnine order (both being white crystalline powders)?   Just trying to give both sides as I see them – and make a plea that you choose carefully and test cautiously if you decide to try this.  One bit of good news is that you’ll probably only ever need to test a single batch, since one $50 order would be a lifetime supply.

(2) Most OTC sterile saline solutions are labeled “not for injection”, which I believe indicates they haven’t been tested as being pyrogen free, and which is one requirement to be USP certified “for injection” purposes.  More on pyrogens here:   There might be other factors I missed that separates “for injection” versus “not for injection” sterile saline.  For infrequent use and in the amount discussed here, the risk seems minimal.   I’d think that factory sealed “not for injection” sterile saline is still a safer option than using distilled water, but I’m not a doctor.

Posted in Homebrew steroids guide.